Packaging information
CTN Szie: 40 × 30 × 20 cm
G.W./CTN:10 kg
QTY/CTN:120 pc/carton
Product specification
1.1 output ability: constant current 30 a, 40 a short-time current (not less than 10 seconds);1.2 the power input: 5.6 V— & ndash; 16.8 V (2-3 quarter lithium battery or 5 & ndash; Section 12 ni-mh/ni-cd battery);1.3 the BEC output: linear regulator, 2 a1.4 high speed: 2 pole motor 210000 r/min, 6 pole motor 70000 r/min, 12 35000 RPM of the motor;1.5 Size: 45mm*24mm*11mm1.6 Weight: 25g
Product features
1. Safety power-on function: when the power is switched on, the motor will not be started immediately no matter the throttle rocker is in any position to avoid personal injury;
2. The throttle trip school callback functions: to adapt to different remote control oilDoor schedule difference, linearity, the response of the accelerator with smooth, delicate touch of speed adjustment and the speed of linear;
3. The program setting project:Brake setting: no brake/brake, factory default is no brake.Battery type: Li - xx (lithium battery)/Ni - xx (nickel cadmium or nickel metal hydride), the default value is Li - xx (lithium battery).Low voltage protection mode: reduced power/off output, default is reduced power.Low voltage protection threshold: low/medium/high, the default value is medium cutoff voltage.When using Li - xx batteries, set up automatically determine lithium electricity number, low/medium/high cases by the voltage of each battery were: 2.6 V, 2.85 V, 3.1 V.When setting using the Ni - xx batteries, electric transfer of electricity automatically detect the battery voltage, as of low/medium/high voltage for the input voltage when the phone is switched on 0%, 45%, 60% (0% means that do not do low pressure protection)Start mode: normal/soft/super soft start, default is normal start.Normal start is suitable for fixed wing and can start the motor quickly in 0.2 secondsSoft start/super soft start is suitable for the helicopter; Soft start and super soft start of the initial rotational speed is low, respectively from the start to the full speed need 1 second and 2 seconds, but if after start-up closed throttle, 3 seconds to start again when they were in normal mode, so as to avoid doing some stunts in flight caused by slow machine.Inlet Angle: low/medium/high. The default value is the inlet Angle.In general, low into the corner can accommodate more motor, but in order to improve the efficiency, suggested that the 2 pole motor use low into the corner, over 6 pole motor used in Angle. In order to improve the speed, into the Angle can be set as Gao Jinjiao. After more improved Angle setting, should first test and then fly on the ground.Restore factory defaults
4. Comprehensive protection functions:Undervoltage protection: set by the user through the program;Over voltage protection: the input voltage more than 18 v does not start, automatic protection, at the same time, a rapid & other; Beep beep beep & throughout; The alarm sound;Overheat protection: built-in temperature detection circuit, MOS tube when the temperature is too high automatic switching off;Remote control signal loss protection, remote control signal loss reduced power after 1 second, have shut down for 2 seconds without a remote control signal output;
Process characteristics
1. The input end of the power supply adopts ** ultra-low impedance and large-capacity electrolytic capacitor, which greatly improves the anti-interference ability;2 output power MOSFET tube is equipped with independent cooling fin, reduce the temperature rise, improve the ability to large current work;3 and controlled by single chip microcomputer;4 SCM independent voltage chip is adopted to avoid the BEC load changes caused by the power interference, improve stability of MCU work;
|
| Set square method |
| 1. Turn on the transmitter and push the throttle to high (The throttle channel of FUTABA series transmitter needs to be selected REV).2, good connection receiver, the motor.3, switch on the power supply, if the transmitter is normal, there will be the following sound :(if the sound is a long sound after the end; Di & throughout; If there is no sound after the sound, check the accelerator channel reverse setting of the transmitter.B stands for LIPO automatic protectionBB BB says NIMH/NICD automatic protectionBBB BBB said the brakesWhen there is no operation, all sounds will continue to loop until an operation is requested.The sound cycle has the Settings you want. When you hear the syllables of the prompt sound (for example, select LIPO Auto protection, and when you hear a B, pull the throttle to the low position), quickly pull the throttle to the low position. At the same time the motor will make a very sharp sound to confirm.At this point, if there are other Settings, quickly push the throttle to the big, you can do the next option of the choice.If your setup is complete, wait 2 seconds for the motor to make a proper battery protection to confirm the sound and confirm the position of the throttle before using it.LIPO automatic protection only two voltage protection, namely 6 v and 9 v, the battery can use full battery unnecessarily.The NIMH automatic protection is calculated based on the actual number of batteries, each battery is set at 0.8V. To accurately determine the battery voltage, please charge the battery. If it is not fully charged, the voltage will be estimated at 70% of the voltage. (You can also use this feature when using 4LIPO)Brakes:Factory Settings are none. A brake setting operation can be performed during actual use, so that the motor USES the counterelectromotive force to brake after turning off the throttle.If you want to remove the brake function, you can set the brake operation again, and the function is cancelled.Factory parameter reset function, because this series of electromodulation has overheat and misoperation protection function, if you find your electromodulation acceleration, or steering, or throttle curve and any other characteristics and how the new changes, then you can do a factory parameter setting to regain high performance. Boot is B a long sound, represent the LIPO electrically controlled automatic protection status, BBB three times, said the NIMH/NICD automatic protection state.
|
Use common sense: (literacy)
Some players pick up the electric adjustment directly onto the plane, the results heard the beep, the motor is not turned, or the speed does not go up, the reasons are as follows:
Time, the use of remote control electric adjustment need to identify large stroke and stroke, as follows:
-- -- -- -- -- - electrical modulation connected to motor electrically controlled line connected to a receiver -- -- -- -- -- open the remote control and push the throttle to high -- -- -- -- -- - turn electric plug in the battery -- -- -- -- -- -- -- listen voice - music (123) -- -- -- -- -- click (throttle high confirmation) - 2 after the throttle lever to the low -- -- -- -- -- to hear three di di di - (throttle lows confirmation note, 2 s 2, 3 s three) -- -- -- -- -- OK
Brushless electric adjustment of 3 lines can be arbitrary, if turn right, to any of these two lines for it.
